Kit Finish Glass La Pajarita

DescriptionFinish Glass is a colorless and transparent two-component varnish (Component A and Component B) that allows us to achieve crystalline finishes of high hardness and brightness. Due to its careful formulation, it is a product that, even with a high viscosity, creates perfectly level surfaces free of bubbles with a 3D effect. It can be applied on a multitude of surfaces: wood, paper, cardboard, metal, plaster, ceramics, stone and any painted surface, providing durable and resistant surfaces, capable of withstanding humidity, cleaning stains..., which is why it is ideal to be able to varnish furniture. such as tables and bar counters. In addition, it does not yellow and offers a resistant finish, but at the same time flexible that does not break due to impacts. Uses1. Crafts with Epoxy Resin on jewelry 2. Epoxy resin on wood 3. Epoxy Resin dyeing 4. Tables with Epoxy Resin 5. Bar varnish or high-use item Application advice1. It is very important that both components are perfectly mixed, otherwise the product will not harden properly and may be sticky or have imperfections on its surface. 2. To improve results, it is convenient that the containers containing Finish Glass are stored at a temperature of 20-23º C before use. 3. When the room where we are working or the containers containing Finish Glass are subjected to low temperatures, the viscosity of the mixture becomes higher and, therefore, a greater number of bubbles are formed during agitation and it also becomes more difficult to release them. For this reason, 5 to 15%, depending on the temperature, of “La Pajarita Finish Glass Solvent” can be added, which will facilitate the agitation of the mixture and later, the leveling and elimination of bubbles during drying. The greater the amount of solvent incorporated, the longer the drying time will also be. 4. The surface must be dry and free of dust, grease, wax... 5. The surface to be applied must be well leveled. 6. For a good leveling and for a perfect job to result, it is important that we drop enough material to flood the entire surface. 7. Mix only the Finish Glass that is going to be used at the moment, since this mixture will begin to thicken and then harden in about 25 minutes. 8. Make sure that the fluid is well distributed without leaving dry spaces. 9. It is advisable to protect the varnished object while it dries, to prevent dust from settling. 10. The excess amount of Finish Glass poured can cause dripping problems on the sides of the pieces to be applied. To avoid this, they can be protected with masking tape or acetate paper. With the latter we can also create forms that serve as a mold on which we will drop Finish Glass and once dry, we will remove the acetate without any problem. 11. One layer is enough, but if you want to apply more than one layer it is enough to clean the surface with alcohol. 12. Woods with an open pore, such as oak or walnut, will require a first coat to seal this pore in order to prevent bubbles from forming from the wood. To do this, prepare half of the mixture that would be used to varnish the surface and spread it with a brush or trowel. Let dry for at least 5 hours and reapply the final layer. 13. On fabric or paper it is convenient to seal before applying Finish Glass, with “La Pajarita Finishes Varnish”. 14. You can use Finish Glass by brush as it comes or reduce it with “Finish Glass La Pajarita Solvent” from 5 to 10%. You can brush freely on any type of painted surface such as stains, patina, glitter without fear of bleeding, without removing the previous paint. 15. Finish Glass can be used as an adhesive with a total dry time of 8 hours. 16. If scratches are made on a surface painted with Finish Glass, polish the affected area and if they still cannot be removed, clean the surface with acetone and pour a thin layer again to renew the surface. 17. If an object is left for a long period of time on a surface varnished with Finish Glass, impressions or marks may remain, but these may disappear within a few hours at temperatures of 21-23º C due to its high flexibility. The higher the environmental temperature, the greater the capacity it will have both to create and to disappear these marks. 18. Finish Glass resists heat, water and alcohol, however, it is not advisable to apply a heat source directly. 19. Not recommended for exterior use.

DescriptionFinish Glass is a colorless and transparent two-component varnish (Component A and Component B) that allows us to achieve crystalline finishes of high hardness and brightness. Due to its careful formulation, it is a product that, even with a high viscosity, creates perfectly level surfaces free of bubbles with a 3D effect. It can be applied on a multitude of surfaces: wood, paper, cardboard, metal, plaster, ceramics, stone and any painted surface, providing durable and resistant surfaces, capable of withstanding humidity, cleaning stains..., which is why it is ideal to be able to varnish furniture. such as tables and bar counters. In addition, it does not yellow and offers a resistant finish, but at the same time flexible that does not break due to impacts. Uses1. Crafts with Epoxy Resin on jewelry 2. Epoxy resin on wood 3. Epoxy Resin dyeing 4. Tables with Epoxy Resin 5. Bar varnish or high-use item Application advice1. It is very important that both components are perfectly mixed, otherwise the product will not harden properly and may be sticky or have imperfections on its surface. 2. To improve results, it is convenient that the containers containing Finish Glass are stored at a temperature of 20-23º C before use. 3. When the room where we are working or the containers containing Finish Glass are subjected to low temperatures, the viscosity of the mixture becomes higher and, therefore, a greater number of bubbles are formed during agitation and it also becomes more difficult to release them. For this reason, 5 to 15%, depending on the temperature, of “La Pajarita Finish Glass Solvent” can be added, which will facilitate the agitation of the mixture and later, the leveling and elimination of bubbles during drying. The greater the amount of solvent incorporated, the longer the drying time will also be. 4. The surface must be dry and free of dust, grease, wax... 5. The surface to be applied must be well leveled. 6. For a good leveling and for a perfect job to result, it is important that we drop enough material to flood the entire surface. 7. Mix only the Finish Glass that is going to be used at the moment, since this mixture will begin to thicken and then harden in about 25 minutes. 8. Make sure that the fluid is well distributed without leaving dry spaces. 9. It is advisable to protect the varnished object while it dries, to prevent dust from settling. 10. The excess amount of Finish Glass poured can cause dripping problems on the sides of the pieces to be applied. To avoid this, they can be protected with masking tape or acetate paper. With the latter we can also create forms that serve as a mold on which we will drop Finish Glass and once dry, we will remove the acetate without any problem. 11. One layer is enough, but if you want to apply more than one layer it is enough to clean the surface with alcohol. 12. Woods with an open pore, such as oak or walnut, will require a first coat to seal this pore in order to prevent bubbles from forming from the wood. To do this, prepare half of the mixture that would be used to varnish the surface and spread it with a brush or trowel. Let dry for at least 5 hours and reapply the final layer. 13. On fabric or paper it is convenient to seal before applying Finish Glass, with “La Pajarita Finishes Varnish”. 14. You can use Finish Glass by brush as it comes or reduce it with “Finish Glass La Pajarita Solvent” from 5 to 10%. You can brush freely on any type of painted surface such as stains, patina, glitter without fear of bleeding, without removing the previous paint. 15. Finish Glass can be used as an adhesive with a total dry time of 8 hours. 16. If scratches are made on a surface painted with Finish Glass, polish the affected area and if they still cannot be removed, clean the surface with acetone and pour a thin layer again to renew the surface. 17. If an object is left for a long period of time on a surface varnished with Finish Glass, impressions or marks may remain, but these may disappear within a few hours at temperatures of 21-23º C due to its high flexibility. The higher the environmental temperature, the greater the capacity it will have both to create and to disappear these marks. 18. Finish Glass resists heat, water and alcohol, however, it is not advisable to apply a heat source directly. 19. Not recommended for exterior use.